EN ISO Research Articles

Testing Activities for Technological and Normative Validation of Bio-Based Components in Façade System Modules

This research explores the development and validation activities of a bio-based façade system within the Basajaun H2020 project, focusing on enhancing the utilization of bio-based components within building envelopes to replace conventional solutions with eco-friendly alternatives. This paper reports the methodologies employed to detect requirements and outline the testing protocols undertaken to validate the façade system design devised within the project, focusing on the original façade components as the biocomposite profile. Vision and opaque façade modules are prototyped and tested following curtain wall standards for performance (EN 13830:2015) and acoustic assessments (EN ISO 717-1:2020) to showcase the efficacy of the developed solution. The conducted tests demonstrate the feasibility of integrating bio-based components as alternatives to conventional materials into building envelopes, aligning with project expectations and prevailing standards for curtain wall façade solutions. Notably, the designed façade system meets technical conditions and research objectives. Nevertheless, the paper underscores the need for further refinements to facilitate solution industrialization and explore broader market applicability focusing on the biocomposite profile.

Interpreting compression resistance and resilience of spacer fabrics with morphological and mechanical changes of different polymeric spacer monofilaments

Customization of spacer fabrics to have the desired compression resistance and resilience is critical to promote their technical applications. The compression properties are mainly determined by the mechanical features of monofilaments used as spacer yarns. This study investigates the compression properties of spacer fabrics knitted with different polymeric monofilaments by analyzing their compression stress at 40% strain, residual strain, and energy absorption from cyclic compression tests. The monofilaments in the fabrics before and after cyclic compression were unraveled to test their tensile properties and morphologies for interpreting their different fabric compression properties. It was found that knitting monofilaments substantially alters their macroscopic and/or microscopic structures, thereby affecting the mechanical behavior of spacer monofilaments, and having different fabric structures and compression properties. Knitting polyethylene terephthalate monofilament damages the mesophase and induces a two-thirds decline in Young's modulus, while knitting polyamide 6 and polybutylene terephthalate monofilaments largely alters the macrostructures but maintains their good resilience. Spacer fabrics knitted with stiffer polyethylene terephthalate monofilaments have superior compression resistance but inferior compression resilience, while those knitted with softer and more resilient polyamide 6 and polybutylene terephthalate monofilaments have better compression resilience. Polyethylene monofilament is not suitable for spacer fabrics because of its low Young's modulus and poor tensile resilience. Polyethylene terephthalate spacer fabrics have the best compression resistance–resilience balance in terms of compression stress at 40% strain and residual strain in the fourth cycle required by the standard EN ISO 3386-1, while polyamide 6 and polybutylene terephthalate monofilaments are more suitable for long-term service due to their high compression resistance and resilience.

Investigation and Optimization of The Effect of Anhydrous Borax Mineral on The Vickers Hardness and Indentation Modulus Values of Iron Material

In this study, 5% and 10% by weight of anhydrous borax (AHB) was added to the iron (Fe) matrix material by powder metallurgy method and the effects of the additive ratio on the Vickers hardness (HV), Brinell hardness (HB) and Indentation modulus (EIT) values of the composites (Fe/AHB) were investigated. In the productions carried out using Taguchi experimental design method, AHB additive ratio, and sintering temperature parameters were selected as control parameters that were thought to affect the physical and/or mechanical properties of the Fe/AHB composite materials. The productions were carried out according to the Taguchi L4 orthogonal array, which was created depending on the control parameters and levels. Vickers hardness and indentation modulus measurements of pure iron and Fe/AHB composite materials were performed in accordance with BS EN ISO 14577-1 standard and Brinell hardness measurement was performed in accordance with TS EN ISO 6506-1 standard. According to the signal-to-noise ratio (S/N) analysis performed with the experimental data, it was determined that the 10% AHB additive ratio and 950oC sintering temperature optimized all the investigated properties of the Fe/AHB composite material. It was determined that the values for Vickers hardness, Brinell hardness and indentation modulus increased by 142.03%, 69.32% and 144.11%, respectively, in the levels where the properties of the composite material were optimized compared to pure Fe material. As a result of the qualitative examination of all samples after storage in a comfortable environment without daylight, it was also observed that the anhydrous borax additive delayed the corrosion time of pure iron material.

From Generation to Reuse: A Circular Economy Strategy Applied to Wind Turbine Production

The environmental impact of wind turbine rotor blades, both during manufacturing and at the end of their life cycle, can be significant. The aim of this study was to define and test a methodology for recycling the waste resulting from their production. Particles of waste from the mechanical machining of rotor blades, which were made up of a glass fibre/epoxy matrix mixture, were used to produce toe caps for use by the footwear industry. The addition of 1 wt.% of particles improved the mechanical properties of the epoxy matrix, with a 5.50% improvement in tension and an 8% improvement in stiffness. Characterisation of the laminates, manufactured by hand lay-up technique, revealed that in the three-point bending tests, the additive laminates showed improvements of 18.60% in tension, 7.50% in stiffness, and 10% in deformation compared to the control laminate. The compression test showed that the additive glass fibre toe cap had greater resistance to compression than the control glass fibre toe cap, with a reduction in deformation of 23.10%. The toe caps are suitable for use in protective footwear according to European standard EN ISO 20346:2022. They guaranteed protection against low-velocity impacts at an energy level of at least 100 J and against compression when tested at a compression load of at least 10 kN.

A spray-on environmentally friendly degradable mulch material and its high efficiency in controlling above-ground biomass of weeds in greenhouse experiments

AbstractThis study describes a novel spray-on mulch material as an alternative to currently used weed control methods. The mulch material is based on renewable raw materials, mainly rapeseed oil, starch and sodium alginate.Laboratory tests were conducted to obtain a mulch material with the best possible properties. Formulations with different ingredients were prepared and tested for their material properties. The formulations were investigated for potential shrinkage tendency and heat resistance as well as water resistance. Further tests such as resistance to mould infestation and aerobic degradability according to DIN EN ISO 17556 were carried out with the formulation that performed best in the previous tests. Mould resistance was enhanced by adding sodium benzoate. In the laboratory experiment, the CO2 decomposition rate was about 30% after seven weeks. With the favouritised variant, which was found step by step through the experiments, an outdoor field test was carried out to investigate the durability under natural conditions over the vegetation period. In the field, the mulch material maintained its function for six months. In the greenhouse, the effect of the mulch material on weeds was studied. It was found that the mulch material showed a high efficiency in controlling above-ground biomass of Elymus repens, Amaranthus retroflexus, and Setaria viridis. In addition, the biomass of the roots of Amaranthus retroflexus and Elymus repens was reduced. Further studies are on the way to elucidate field suitability and the weed suppressive effect under different environmental conditions.

Thermoregulation of Feet in Cold Environments: A Study on Alpinism

Thermal comfort plays a crucial role in the performance and well-being of mountaineers, especially in extreme environments. The aim of this study was to develop a reliable protocol to assess the thermal comfort of mountaineering boots, with a specific focus on temperature variations in different regions of the foot and their correlation with physiological factors. Two different models of mountaineering boots were tested at two different environmental temperature (-15°C and -30°C). The mean skin temperature, measured according to International Standards BS EN ISO 9886:2004, was used as an indicator of overall thermal comfort. Physiological factors such as heart rate (HR), body mass index (BMI) and body surface area (BSA) were also measured to understand their relationship to thermoregulation. Kruskal-Wallis and Pearson's ProductMoment correlation tests were performed to investigate whether there was a statistically significant relationship.The results showed significant differences in foot temperature among the Testers, indicating variations in the perception of thermal comfort. The correlation analysis showed a strong positive relationship between mean skin temperature and HR, highlighting the influence of physiological factors on thermal comfort.In addition, the analysis showed that the dorsum and hallux areas had the largest temperature variations, suggesting the occurrence of vasoconstriction and potential discomfort.This study represents a preliminary approach to establishing a reliable protocol for assessing the thermal performance of cold protective footwear.

R290 Refrigerant Performance in a Commercial Refrigerator

In this study, we investigated the impact of the environmentally friendly R290 refrigerant, which has a higher Coefficient of Performance (COP), on the operating performance of the cooling system, as an alternative to the commonly used R404A refrigerant, which has a negative effect on global warming. The boundary conditions in the refrigeration cycle were designed to be -10°C evaporation and +45°C condensation, and the performance of the system referenced in the TS EN ISO 23953-2 standard was experimentally compared for both refrigerants. The temperature and energy consumption values of the M-packs, whose location and quantity are specified in the relevant standard, have been evaluated in terms of the cooling performance of the cabinet. As a result of the study, the heat removal performance of the system using R290 fluid in the condenser showed better results compared to R404A. According to the relevant standard, the system using R290 is in the C and D classes in the energy consumption evaluation.

Potential of solid recovered fuel production from autoclave treated healthcare waste in Sultanate of Oman

ABSTRACT Economic growth has a potential impact on waste generation worldwide. Growing recognition for resources recovery from waste including production of a clean energy has led to the development of standards for, and the generation of, Solid Recovered Fuel (SRF). SRF, according to BS EN ISO 21640 is a fuel prepared from nonhazardous/treated waste to be utilized for energy recovery in incineration or co-incineration plants which meets the classification and specification. The amount of combustible fractions (i.e., plastic, textile and paper) that are present in Healthcare Waste (HCW) and Municipal Solid Waste (MSW) provides an opportunity for SRF production. HCW is defined as clinical waste generated from healthcare facilities. Limited efforts in utilizing treated HCW in production of SRF were noted, despite the fact that high content of combustible fractions, hence the novelty of this research. This research addresses the opportunities of utilizing autoclaved HCW as an alternate fuel; through a detailed chemical and physical analysis of autoclaved HCW collected from the Sultanate of Oman hospital and healthcare facilities. Furthermore, this study examines the possible uses of such materials instead of landfilling. The utilization of treated HCW as an alternative fuel is not only saving the land space, but also reduces the carbon emissions originating from landfilling. This in fact would also support the government in achieving its aspiring goal of the net zero carbon emissions by 2050 through better utilization of these materials in production of SRF as an alternative to fossil fuel combustion. The study revealed that autoclaved HCW appears to have a high quality SRF and is classified as (NCV 4, Cl 3); which complies with the potential end users’ specifications. It is estimated that the combined energy output from MSW and HCW combustible fractions could cover about 12.75% of the energy requirements for Oman cement factories. Implications: The results confirm the viability of using autoclave (HCW) as an alternative fuel due to its high thermal energy content. Based on mean Net Calorific Value (NCV) of analyzed HCW that is found around 14 (MJ/Kg (ar)), and the mean Cl level (i.e., 0.814 ± 0.213% (d)); the SRF is classified as (NCV4, Cl 3). This grade is found to be well within the end users accepted range. This opens up the opportunity for creating a market demand for HCW that not only it could boost its recovery, but it could also unlock the value that can generates.

Phenol-formaldehyde resin enriched with graphene nanoplatelets as an electroconductive adhesive for wood composites

The study demonstrates that phenol-formaldehyde (PF) resin, commonly used for lignocellulosic composites, can become electroconductive when modified with graphene nanoplatelets (GNPs) while still serving as an effective adhesive for particleboard production. The PF resins enriched with various amounts of GNPs were tested for viscosity, gel time, and thermal stability, followed by electrical conductivity measurements for GNP-enriched resins applied to several lignocellulosic surfaces of varying wettability. These tests showed that the optimum weight percentages of GNP at which the resins maintain both the electrical conductivity and process parameters, enabling the formation of particleboard, amount to 18.5%. Consequently, a prototype of electroconductive particleboard was created and evaluated for bending strength (EN 310: 1993), modulus of elasticity (EN 310: 1993), tensile strength (EN 319: 1993), thickness swelling (EN 317: 1993), water adsorption (PN-76/D-04234) and formaldehyde emission (EN ISO 12460–5:2015). Impressively, the panels achieved a conductivity of 320 Ω m, indicating their potential use as resistive heaters and other applications in the Internet of Things (IoT) area. Simultaneously, the GNP-enriched panels showed formaldehyde emission well below the threshold set by the standards and exhibited mechanical properties that in most cases met the criteria for use in furniture and interior design.

INFLUENCE OF FILLERS ON THE STRUCTURE AND PROPERTIES OF POLYMER MATRIX

Purpose. Enhancement of the mechanical properties of the polymer matrix through the incorporation of finely dispersed fillers, namely aluminum oxide and talc, as potential modifiers.
 Research methods. Research was conducted on polymer specimens subjected to tensile testing according to DSTU EN ISO 527-5:2018. The tests were performed using a URM-5 tensile testing machine with a maximum force of 50 kN. Metallographic analysis was carried out using a KEYENCE VHX microscope at magnifications of 50 and 500. The microstructure of the polymer matrix was assessed through etching-free procedures.
 Results. The study demonstrates that the incorporation of finely dispersed aluminum oxide particles increased the strength parameter from 4.69 MPa to 13.07 MPa, as compared to the unfilled sample. Additionally, it was observed that the introduction of finely dispersed talc particles at a concentration of 0.75 % by mass led to an enhancement in strength values from 4.69 MPa to 12.74 MPa, in comparison to the unfilled sample.
 Scientific novelty. A polymer matrix with enhanced mechanical properties was achieved through the addition of fillers acting as modifiers. The optimal concentration of aluminum oxide and talc additives was determined. By comparing the results with previous studies involving aluminum oxide and talc at various concentrations in different types of polymer matrices, it can be concluded that the investigated concentrations of modifiers with epoxy resin ED-20 led to the production of a polymer composite with superior mechanical characteristics. The obtained results underscore the significant potential of aluminum oxide and talc as effective modifiers for improving the strength and other crucial properties of composite materials.
 Practical value. The obtained results highlight the significant potential of utilizing aluminum oxide and talc as modifiers for polymer matrices to enhance their mechanical characteristics. From a practical standpoint, the use of these fillers can exert a substantial impact on the development of new composite materials with improved properties, finding application in composite reinforcement production. Considering the heightened strength and resilience of the resulting materials, these composites can be effectively employed to create lighter and stronger structures in construction and other industries. Additionally, their application may lead to reduced repair and maintenance costs due to increased durability and resistance to mechanical loads. Thus, the implementation of the obtained results could have a substantial influence on the practice of composite material manufacturing, ensuring the creation of products with enhanced characteristics for various applications.

Joining aluminum die castings and wrought aluminum by resistance spot welding

Resistance spot welding (RSW) is an economic, robust welding process, which is easy to automate and widely used in automotive industry. In this work, the resistance spot weldability of die-cast aluminum alloys EN AC-AlSi7MnMg, EN AC-AlSi9Mn and EN AC-AlSi10MnMg-T6/T7 to wrought aluminum alloy EN AW-AlSi1MnMg-T6 is investigated when applying the standard welding profile as recommended in VDA 238-401 considering main challenges in welding aluminum die castings, for example, porosity and inhomogenities. Weldability is best for EN AC-AlSi10MnMg-T6/T7, but the results show limited applicability of VDA 238-401 in general, especially for high total sheet thicknesses, because of invalid electrode force favouring spatter formation and weld spot irregularites. Still, all spot welds between die castings and 2 mm wrought aluminum sheets reach the recommended shear tension forces for spot diameter dw of 5·√t (2 mm: 5.95 kN; 3 mm: 8.96 kN; according to DIN EN ISO 18595), although being afflicted with solidification porosity and liquation cracking. Gas porosity is not observed and solidification porosity is only found to be significant for weld spot failure when being located close to the joining level, which is observed at welding depths of approximately 50% into the wrought aluminum sheet. Here, a failure path across the nugget is found. Weld porosity apart from the joining level is less significant and failure path is found along the fusion line between nugget and wrought aluminum. Instead, hardness difference between nugget and HAZ is the main reason for weld spot failure. Although the applied welding current profile is not suited best for RSW of mixed joints between aluminium die castings and wrought aluminium alloys, the results confirm its potential, for example, a significantly reduced gas porosity compared to applied fusion welding processes.

Corrosion Behavior of Zn-Al-Mg-Si Coatings in Sulfur Dioxide-Containing Environment

Zn-Al-Mg-Si coatings are an excellent alternative to conventional hot-dip galvanizing coatings. Their high corrosion resistance in corrosive environments containing chlorides and CO2 is well recognized. But sulfur dioxide is also an important stimulator of corrosion in the atmospheric environment. This article presents the results of microstructure (SEM/EDS/XRD) and corrosion behavior tests of Zn-Al-Mg-Si coatings obtained by a double hot-dip method on HSLA steel. The corrosion resistance of the coatings was determined in the sulfur dioxide test with general condensation of moisture (EN ISO 6988). In the corrosion test, Zn-Al-Mg-Si coatings showed twofold smaller weight loss compared to conventional hot-dip zinc coatings. It was found that the corrosion behavior of coatings was influenced by the structural components revealed in the outer layer: Al-rich dendritic and interdendritic areas with Zn/MgZn2 eutectic, MgZn2 intermetallic and Si precipitates and their electrochemical nature. The increase in corrosion resistance was caused by the formation of beneficial corrosion products: layered double hydroxides (LDHs) based on divalent Mg2+ and Zn2+ cations, trivalent Al3+ cations and SO42− anions, and zinc hydroxysulfate—Zn4SO4(OH)6∙5H2O. The presence of Si precipitates could cause pitting corrosion of coatings.

Membrane filtration for enumeration of Listeria monocytogenes at low levels on salad leaf

The reference method BS EN ISO 11290-2:2017 is insufficiently sensitive to enumerate Listeria monocytogenes in most commercially prepared leaf salads. A more sensitive method for enumerating low levels of Listeria spp. is required to evaluate the impact of process changes and the effect of Listeria control mechanisms in chilled foods including salad leaf. Membrane filtration allows larger volumes of food to be tested but care must be taken to avoid excessive pigmentation of the membranes by damage to leaf during sample preparation and bag homogenisation. Blue-green colonies can be identified after 48 h of incubation of the membranes on Listeria Ottaviani and Agosti selective agar plates, these colonies are indicative of Listeria spp., but halo zones cannot be distinguished. Results obtained by this technique are reported showing enumeration of 5 CFU/g added L. monocytogenes.

Statistical evaluation of hard-to-measure surfaces

The main goal of this article will be to find ways to evaluate hard-to-measure surfaces statistically. First, the basic characteristics and rules of surface quality will be described according to the standards ČSN EN 4287, ČSN EN 4288 and ČSN EN ISO 2517-2. Subsequently, the measured values of the roughness parameter Sa (arithmetic average of the height of the measured surface) and Sz (the maximum height of the measured surface) will be compared and evaluated which is the best. These parameters will be described and measured on aluminium plates on which the test surfaces were laser engraved. To evaluate the best surface, statistical methods will be used, such as the EDA methodology (exploratory data analysis), hypothesis testing with normality and outlier tests, and last but not least, cluster or cluster analysis, which compares the similarity of the measured data. This article aims to show the possibilities of surface quality assessment using 3D surface roughness parameters, which are not often used in practice.

The Importance of Application of EN ISO 3834 and EN 1090 in Production of Steel Structures

Fractures of welded structures in operational conditions most often occur in the welded joint or its immediate vicinity. Due to this, special attention is paid to ensuring the quality of the welded joint. The application of the EN ISO 3834 and EN 1090 standards in the manufacture of steel structures aims to ensure the highest possible quality of welded joints, and thus the quality of the structures as a whole. Weld quality is achieved by welding, whereas weld quality control provides a check of product reliability. Increasing requirements in terms of reliability, better use of materials, lower weight and cost of constructions, but also high use of load-bearing structural elements, and thus welded joints, leave less room for errors in welded joints, which is why constant control and monitoring of documented procedures is required.

NLCA in bakery food products: state of the art and urgent needs

This study analyzes the nutritional life cycle assessment (LCA) of bakery products and the current state of the art. The analysis focuses on (1) the importance of applying a methodology, such as LCA, in a general way and the division into different stages considering the UNI EN ISO; (2) the development of nutritional LCA; (3) the difference between functional units in LCA and nutritional LCA; and (4) the different nutritional LCA approaches. The study emphasizes the lack of nutritional LCA studies regarding the bakery category, underlining the urgent need for this type of investigation concerning this specific food sector.

Polyhexanide based contact lens storage fluids frequently exhibit insufficient antifungal activity against Fusarium species

PurposeFusarium keratitis is a severe infection of the anterior eye, frequently leading to keratoplasty or surgical removal of the affected eye. A major risk factor for infection is the use of contact lenses. Inadequate hygiene precautions and mold-growth permissive storage fluids are important risk factors for fungal keratitis. The aim of this study was to comparatively analyze contact lens storage fluids disinfection efficacy against Fusarium species. MethodsEleven commercially available storage fluids were tested. The storage fluids were classified according to their active ingredients myristamidopropyldimethylamine (Aldox), polyhexanide and hydrogen peroxide. Efficacy was tested against isolates belonging to the Fusarium solani and Fusarium oxysporum species complexes as the most common agents of mould keratitis. Tests were carried out based on DIN EN ISO 14729. ResultsAll Aldox and hydrogen peroxide (H2O2) based fluids were effective against Fusarium spp., while the majority of polyhexanide based storage fluids showed only limited or no antifungal effects. Efficacy of polyhexanide could be restored by the addition of the pH-regulating agent tromethamine - an additive component in one commercially available product. ConclusionsIn summary, the use of Aldox- or hydrogen peroxide-based storage fluids may reduce the risk of Fusarium keratitis, while polyhexanide-based agents largely lack efficacy against Fusarium.

Migration of plasticizers from flexible PVC: Monitoring the concentration profiles by confocal Raman microspectroscopy

This study introduces and validates an effective approach for monitoring the plasticizer amount and its concentration profile in polyvinyl chloride (PVC) formulations. The method combines gravimetric measurements with confocal Raman depth profiling analysis. Several flexible PVC (pPVC) formulations were compared in this study, including: pPVC@DEHP, using the monomeric plasticizer di(2-ethylhexyl) phthalate (DEHP); pPVC@PBA, using the polymeric plasticizer poly(butylene adipate) (PBA); and crosslinked pPVC (cPVC@DEHP), where isophorone diamine (IPDA) served as the crosslinker. Migration tests were performed according to UNI EN ISO 177 standard. Spectroscopic findings were correlated with gravimetric data, highlighting strong differences in the migration behavior among the formulations. The results demonstrate the effectiveness of the proposed method in quantifying plasticizer leaching and obtaining detailed concentration profiles at fine scale.

Evaluating Cleaning Services in Civil Environments: Microbiological and Life Cycle Analysis Comparing Conventional and Sustainable Methods

In response to the growing global concern for environmental sustainability, a Life Cycle Assessment (LCA) study was conducted to evaluate the environmental benefits of the “Formula Servizi” GREEN protocol compared to a conventional cleaning protocol, as mandated by the updated Criteria for Environmental Sustainability (CAM—Criteri Ambientali Minimi) for cleaning services. The CAM, effective on 19 June 2021, requires companies to demonstrate the environmental advantages of their cleaning protocols over traditional methods. This study aligns with the new CAM guidelines and employs UNI EN ISO 14040–14044 technical standards for a comprehensive comparative analysis. The study highlights the significance of maintaining hygiene to ensure safety in various contexts, emphasizing the importance of environmental sampling and monitoring to prevent contamination and infection transmission. Despite the complexity and expenses associated with microbiological monitoring, this research affirms its crucial role in validating cleaning procedures, particularly in healthcare facilities, food service areas, and industrial settings. The findings reveal that both the “Traditional” and “GREEN” cleaning protocols demonstrate satisfactory effectiveness in controlling microbiological contamination according to established guidelines. Moreover, the LCA results indicate that the “GREEN” protocol, while exhibiting higher water consumption and wastewater treatment, showcases a strategic use of more sustainable cleaning and laundry detergents. Despite the increased water usage in certain phases, the significantly lower environmental impact per unit of weight demonstrates the potential for optimizing both environmental sustainability and operational efficiency in future Life Cycle Sustainability Assessment (LCSA) endeavors. The comparative LCA further reveals that the “GREEN” protocol enables an annual avoidance of 260 g of CO2-e emissions per square meter of cleaned surface. The most significant reduction in absolute terms is associated with the use of eco-labeled detergents in the laundry system, resulting in the avoidance of 654.1 kg of CO2-e per year of service (−77% compared to traditional laundry detergents).

In full swing: Analytical strategies for the conservation assessment of operating Industrial Heritage machinery

The condition assessment of Industrial Heritage machinery in operation is an open research subject of utmost importance for defining conservation and maintenance plans. The present work approaches this issue by proposing the study of Industrial Heritage machinery that includes the assessment of substrates, coatings, lubricants and operating mechanisms by applying analytical techniques currently used for heritage studies together with techniques employed in condition monitoring of modern machinery. An early 20th century steam engine from the Vale de Milhaços Gunpowder Factory (Portugal), in operation for demonstration purposes, was selected as a case study. The engine metallic alloys and coatings were studied by XRF and Raman spectroscopies, and the main properties of lubricants studied according to EN ISO and ASTM standard tests. Metallic particles present in the oil due to wear were assessed by XRF. The mechanisms were examined by gamma radiography, magnetoscopy, thermography and vibrational analysis.Data showed the use of distinct alloys according to the engine components' function similar to those reported for the same period. Green copper phthalocyanine and toluidine red identified as coatings’ pigments are typical from the late 20th century and thus ascribed to a previous repair. The properties of the fresh and used lubricants are slightly different but without evidence of a significant alteration that could endanger the machine's functioning. However, the presence of metallic particles in the oil suggested the existence of wear phenomena. The engine's operating speed (51 rpm) and the vapour temperature (≈154 °C) attained inside the cylinder were indirectly determined. The presence of cracks on the engine structure was assessed, and possible faults that can imperil the engine functioning were analysed. The vibrational analysis of equipment in operation revealed a lack of lubrication and wear on the feed pump journal bearings.